AgriTotal is New Zealand's exclusive importer of Vervaet machines for harvesting and managing slurry. View their beet harvesters and hydrotrikes online. VERVAET Q SERIES Models Q616 and Q621 The successor to the Beet Eater 617 has been in production for 23years and is finally here! Vervaet have designed an all-in-one machine catering to almost all demands on the market today. The name Q-series comes from "Quad", it's a 4-wheeler. The rear wheels are mounted close together, to provide the same advantage as a trike - the wheels each run in their own track. The machine can perform under all circumstances. The Q-series was developed modular, allowing features to be customisable. There are three toppers available. 2 types lifting units 2 tank sizes two engines 4 different chassis options. The different options create 288 possible editions within the Q series. PRODUCT INFORMATION Tyres Frame Tank Engine Toppers Cleaning Electronics WATCH VIDEO VIEW GALLERY QTyres Tyres Both front and rear axle offer a choice in tyre sizes. At the front, there can be 710x42, 800x38 or 900x38 mm tyres, while at the rear the selection consists of 800, 900, 1000 or 1050 mm, all of them 32 inch rims. The latest in ultra-flex tyres from different brands can be fitted. Our expectation is to be able to drive the Q-616 just over 1 bar. Like our 9 row Beet Eater, with its pyramid arrangement of the wheels, the new Q-series wheels only have 1 passage. It is a huge advantage compared to 2 or 3 passages in a track, because the soil compaction is greatly reduced. We would like to note that crab-steering harvesters also claim to have one wheel passage, while their wheels partly run in the same track 2 or 3 times. Due to the rear axle which is mounted on a turntable, the machine is highly maneuverable, with an inside turning radius of only 2.4m. The front wheels are also steered with an angle of 8 degrees. The front axle is a pivoting axle, with hydraulic cylinders to allow the machine to hang on against slopes, making it more stable, while at the same time, reduce the weight on the wheel on the valley-side, thus also preserving soil quality. Optionally available is a fully automatic leveler controlled by a G sensor. The Q-series has tyre inflate systems as an optional extra. This allows the operator to inflate or deflate the tyre pressure on-the-move. In addition to the tyre options, it is also possible to equip the machine with a rubber tracked front axle. This will greatly increase the contact surface of the front axle, which results in a lower ground pressure per cm2. The major difference in comparison with the 617 on tracks, lies in the fact that the Q-series does not need to be equipped with a different harvesting unit. It can be simply adapted on a standard machine, which can then be switched at any time from tyres to rubber tracks. Frame Another innovation is the tilt T-fork. It can commute, just like the front axle. This makes it possible to let the whole machine tilt to the left or right. The rims have an offset of 10 cm, and can be mounted left or right on the wheel drive, so that one can choose from a narrow or wide wheel base. In the wide arrangement, the outside wheel track measures 2.80 meters with a spacing of 70 cm. In the narrow set-up, it is only 30 cm. It is conceivable that users on steep slopes will opt for the wide set-up. Or those who prefer to leave a strip of land un-touched by the wheels. QFrame Tank Not everyone is charmed by a large tank. Increasingly we have demand for a lighter machine. We have chosen to offer the new Q-series in 2 variants: Q-616 and Q-621. The Q-616's has a fixed ring elevator and distributing auger. The capacity is calculated at 16 tonnes. However, to compete against the colleagues with the dog walk machines, we also needed a larger version. The Q-621 has an extendable ring elevator, auger and side extensions. As the name suggests, the capacity of this version is 21 tonnes. The ring elevator is 20% wider than the previous 617 model, in order to smoothly charge the greater yields with less damage. Should the yield be lower, the speed can be further reduced which gives longer life and lower fuel consumption. The discharge elevator is completely renewed. It now sits at the front of the tank, which gives a perfect view at the unloading process, and also keeps the machine's center of gravity low. The width is 1.40m, to better fill out trailers. The length of the valve is increased with no less than 80cm. This allows us to discharge higher and/or further. By tilting the front axle, the height of the discharge elevator can further increase or reduce by 50cm. (450cm max. and 190cm min.) Due to the ever-increasing trailer sizes as well as the desire to unload directly into lorries, it’s an important feature. The lower position is to reduce damage to the beets when starting to build a new heap. The length of the elevator ensures a safe distance from the wheels to the beet heap. The side boards are made of straight sheet metal in order to minimize damage to beet. The position of the elevator can be programmed for both the working position and the unloading position. The tank floors automatically switch on one by one so that the discharge elevator will not be overloaded. Tank Engine The Q-616 is equipped with a 465horsepower motor with DAF, same as the previous 617 model. The Q-621 features 510horsepower. Both engines work at a low 1100 rpm to 1350 rpm. The fuel consumption of the last 617 had been brought back to around 30 litres per hour. QEngine Toppers We offer three toppers: 1) Integral, which chops the leaves and puts it between the rows. Advantages: Low maintenance, lightweight and compact. 2) Combi, working integral or with leaf spreader. Advantage: it’s ready for all conditions. Both the Integral and Combi can be equipped with the new multi-topper scalpers, that are guaranteed to give the best topping result, which nowadays is, taking off the leaf, but not cutting off the head of the beet. 3) Combi with Double Rotor, which has no scalpers and thus saves the entire head of the beet. Advantages: It’s the latest trend in defoliation but sadly not a good choice in stony areas. QToppers Cleaning Different types of soil require different cleaning systems. Vervaet have designed the machine with four options of cleaning systems available: 3 cleaning turbines, one belt 5 cleaning turbines 6 cleaning turbines 5 cleaning turbines and axial roller bed You can also choose the turbine type or gates in all four. The diameter of the turbines has grown 8% in order to allow an even better flow. QCleaning Electronics The Q-Series is equipped with all comforts, including: Automatic lubrication, Auto. 4 wheel steering, Auto. Depth control of the harvester Auto. Depth control topper Auto. Tank Discharge Auto. RPM adjustment of machine functions according to forward speed. Auto speed adjustment engine when stationary / driving / unloading bunker Auto on and off machine at lowering / raising harvester and topper Reversing direction all machine functions Presets for setting machine to different circumstances. Auto speed setting (Cruise) Diagnostic system on almost all functions Fuel consumption meter per hectare and per hour capacity meter camera system LED-lighting Auto speed control of the engine: In neutral, the engine reverts to idle speed, in harvesting mode it goes to the set speed, and while unloading on the heap, it also drops to 1100 rpm. QElectronics For more information about products, accessories or prices, please contact us.

AgriTotal is New Zealand's importer of Horger Maschinen's Athletic Track Cleaners for cleaning synthetic sports tracks. ATHLETIC TRACK CLEANER KBR AgriTotal are New Zealand's importer of Horger Maschinen Athletic Track Cleaners. Sports facilities equipped with synthetic coverings offer advantages including antislip surface, elasticity, water permeability, and therefore reduce accident risk. However, such surfaces will lose their effectiveness within a few years if they are not maintained due to penetration of dirt particles and alga forming. Horger developed the athletic track cleaner for high pressure cleaning. It cleans and collects the dirty water in one process, and can be fitted to compact and narrow gauge tractors. The athletic track cleaner consists of a cleaning unit which is attached to the front of the tractor, and a tank pump unit is fitted to the rear of the tractor. The rear tank is divided into a fresh water part and a dirty water part. The fresh water is sucked in by a high pressure pump, which is driven by a drive shaft, and carried via hoses to the front cleaning unit. The water is effectively brought to the bottom by 4 nozzles that are fastened at two circling rotors. At the same time the front cleaning unit is set under vacuum and the water with the removed dirt is taken up through an injection pump into the rear tank. The dirty water can be emptied later through a tap. WATCH VIDEO GALLERY For more information about products, accessories or prices, please contact us.

CLEANFIX is revolutionizing engine-cooling systems. Our reversing fan solutions clean radiators, contribute to optimal cooling and extend the lives of machines. BM AIR CLEAN CABIN AIR Get in touch with us to sort out your clean cabin air needs today! GET IN TOUCH Clean air is critical for peoples health, especially in workplaces in polluted environments. A BMAir pressurised filter system cleans the air entering the control cabin and thus ensures optimal protection for the occupants. Furthermore, the system offers stae of the art monitoring and warning signals. Optionally, the control unit can log all recorded cab data so that you can control the work environment and can respond adequately to any exposure to toxic substances. Operation of the BMAir pressurised filter system The BMAir pressurised filter system is mounted on the roof of the cabin or on the deck of the machine. The polluted air is sucked in through the inlet of the system. The coarse dust particles are first filtered out, followed by fine dust using a HEPA filter. Gases and vapors are then removed by the active carbon filters. The blower drives the filtered breathing air into the cabin. The monitoring system checks, the cabin overpressure, the lifespan ofthe filters and optionally the air quality by means of additional sensor (s). Excess air exits the cab through any remaining seams and cracks. A green light on the roof is optional and indicates that the system is fully functional. BMAIR Brochure To play, press and hold the enter key. To stop, release the enter key. FILTER PRESSURIZATION SYSTEMS BMAir has a wide range of pressurised filter systems. Each BMAir system can be equipped with a filter package tailored to your specific working environment. In combination with our control systems, there is a solution for every workplace. Our experts have extensive knowledge of which system best suits your work environment and can advise you in combining the system with the appropriate control system and filter package. BMAir MAO-2 Nowadays, construction machines are more streamlined and have limited space for the installation of a pressurised filter System. The BMAir MAO-2 was introduced for this purpose. Smaller, powerful, mountable in various positions and suitable for practically every construction machine. • Weight: 35 kg without filters • Dimensions: 626 x 355 x 384 mm (L x W x H) • Filter capacity : 23 litres • Material: Stainless steel

AGRITOTAL SUPPLIES PATEER PARTS. TAKE A LOOK AT OUR RANGE HERE PATEER FRONT WEIGHTS ST - STEEL RANGE B SERIES - CAST IRON RANGE MUFO 2 - CAST IRON RANGE BF RANGE - FENDT DESIGN FP BBL - CAST IRON RANGE FP BBL HDC - INTEGRATED STORAGE NEW RT - FP-HPDE POLYETHYLENE RANGE RT CB - FP-HDPE - POLYETHYLENE RANGE DEUTZ FAHR - 800,1000,1200 ST - STEEL RANGE Description The result of our ongoing commitment to offering innovative, high-quality products that are accessible to all budgets, the ST RANGE is the successor to the former FP-WEL steel range. Particularly well thought-out in terms of design, size and front adhesive marking (striking, neat, eye-catching), the ST serie is resistant, versatile and contemporary. Advantages Steel, a guarantee of quality: resistant to impact, weathering, crack propagation and deformation Robust et durable Perfect finish With its modern design and smooth, clean surfaces, the ST counterweight gives a perfect finish to the tractor's overall appearance. Its clean lines are in perfect harmony with the sleek, powerful styling of today's models. Attractive front adhesive branding, customizable for brand, dealership or end customer. Modular → available in an upgradeable model with a casted add-on unit to be inserted from below for consistent integration Description The result of our ongoing commitment to offering innovative, high-quality products that are accessible to all budgets, the ST RANGE is the successor to the former FP-WEL steel range. Particularly well thought-out in terms of design, size and front adhesive marking (striking, neat, eye-catching), the ST serie is resistant, versatile and contemporary. Advantages Steel, a guarantee of quality: resistant to impact, weathering, crack propagation and deformation Robust et durable Perfect finish With its modern design and smooth, clean surfaces, the ST counterweight gives a perfect finish to the tractor's overall appearance. Its clean lines are in perfect harmony with the sleek, powerful styling of today's models. Attractive front adhesive branding, customizable for brand, dealership or end customer. Modular → available in an upgradeable model with a casted add-on unit to be inserted from below for consistent integration Return to Front Weight Menu B SERIES - CAST IRON RANGE Description A guarantee of quality ; shock, crack propagation and deformation resistant ; lasts through time. B line is highly modular and provides a wide variety of weights. Advantages Compact units with minimum projection A tool carrying frame adds further possibilities for combined transportation A 400, 600kg or 800kg add-on weight bolted to the front of any of the base units provides extra flexibility Technical Characteristics Dimensions Standard equipment Suitable for front linkage (300kg model is suitable for cat. 1 & 2 linkages / specialist tractors) Integrated coupling jaw to the 3rd link Optional equipment 400, 600 or 800kg add-on weight Bumper of any of our ranges (TRACTOR-BUMPER CONNECT on B 600 and B 900kg models / B-PROTECT on any model / BUMPY on any model) Tool carrying frame Fp-Box storage compartment Dealer logo Return to Front Weight Menu MUFO 2 - CAST IRON RANGE Description A guarantee of quality ; shock, crack propagation and deformation resistant ; lasts through time. Mufo-2 range is characterised by its modern design, in perfect harmony with tractor’s bodies. Advantages Very compact, with minimal forward extension to the linkage arms Mounted to front linkage or directly to weight frame A 500kg add-on weight fixed to the front of any of the base units provides extra flexibility Technical Characteristics Dimensions Standard equipment Suitable for front linkage Integrated coupling jaw Optional equipment Back plate to mount directly to the tractor weight carrier 500kg add-on weight Fp-Box storage compartment Dealer logo Return to Front Weight Menu BF RANGE - FENDT DESIGN Description The exclusive Pateer Fendt cast iron weight meets the very highest quality standards and stands as a guarantee of resistance to shocks and exceptional durability. Advantages The Fendt range is very compact. Its rounded side (400 and 870kg) can be mounted either forwards or backwards. The notches on the 870 and 1400kg models allow the addition of 400 or 600kg weights from the B range, or Fendt jerrycan Available weights 400kg - 870kg - 1250kg - 1400kg - 1800kg - 2500kg Return to Front Weight Menu FP BBL - CAST IRON RANGE Description Our new FP-BLL combine pleasing, modern design with outstanding quality, durability numerous practical advantages and a wide range of capacities. Cast iron weights are resistant to impact, time, crack propagation and deformation, which is a guarantee of quality. Very cleverly designed, it incorporates a generously proportioned toolbox compartment with a capacity of some 80 litres. ADVANTAGES Aesthetically pleasing 80L Storage space on the top With 400, 600 and 800kg add-on weights available on the front and 500kg underneath, provides the weight capacity to suit your tractor and application. Technical features Standard equipment Front linkage fixing including: - 3rd link ⌀25mm pin - Coupling jaw to the 3rd link 80LStorage space integrated - Box size : 980 x 230 x 310 OPTIONAL EQUIPMENT 400, 600 or 800kg additional front weight to be mounted with weight holder (case iron range B) 500kg additional weight to be mounted from below Sliding elements make it possible to adjust wings size according to the size of the tractor Fp-Box storage box Safety kit with position indicators, limiting lights, reflective strips Fp-Box storage compartment Dealer logo Return to Front Weight Menu FP BBL HDC - INTEGRATED STORAGE Description Don’t worry about juggling all your tools while driving your tractor. This ballast box will neatly store your gear and accessories, as it’s very cleverly designed and comes with an integrated storage compartment. Made of magnetite, an innovative, high quality material (density 2.5 times greater than reinforced concrete), the price is affordable. Advantages 73L Storage compartment on the top Weights available: 1000kg | 1200kg | 1400kg the external dimensions and profile of the block remain the same throughout the range, due to the composite construction allowing material density to be increased, rather than the physical size of the block, to provide additional capacity Clean, modern, aesthetically pleasing with advanced properties that deliver important benefits TECHNICAL FEATURES Standard equipment Front linkage fixing kit Coupling jaw to the 3rd link 73-litre toolbox storage area Optional equipment Bumper function (adjustable sliding elements) Enhanced security kit (Soft limiting lights, reflective strips) Return to Front Weight Menu NEW RT - FP-HPDE POLYETHYLENE RANGE Description The new RT weight range combines a highly innovative polyethylene outer shell filled with a variable density concrete core. • The outer shell, produced according to the specificities of the rotomolding technique, is resistant to shocks, time, cracks and chipping. • Its modern and sleek curves give a very accomplished appearance matching the general appearance of today's tractor, compact, powerful and ergonomic. • Branded Plastron (tractor's brand logo and color). • Optional: Branded frontal polycarbonate plate (instead of plastron) - tractor's logo or dealer's logo RT range offers basic models (see RT) or models with integrated storage compartment (hereafter) Advantages High-density polyethylene outer shell, a material that combines strength, exceptional durability and zero maintenance Integrated storage compartment (740x270mm - Ht 300mm) Low environmental impact Economic Unalterable color, even in the event of shocks, scratches, scrapes or scratches Technical caracteristics Return to Front Weight Menu RT - CB DESCRIPTION From high density polyurethane (HDPU), a material that combines strength, exceptional durability and zero maintenance The geometric lines emit a modern, pleasing and balanced design and give a very accomplished look to the overall look of today's compact, powerful and ergonomic tractor ADVANTAGES Solid : Shock absorbing Resistent : it is not afraid of rust, impact, time, cracks and deformation. Colors unalterable : Material that does not peel Low environmental impact : no painting stage. Made from recycled materials (plastic shell and concrete filling) TECHNICAL FEATURES Standard equipment Front linkage mounting kit -cat. 2 from 400 to 1200kg (piton plate) Coupling jaw to te 3rd link Eco Friendly Utilization of production surpluses Crusher for sorting, cutting, crushing of polyethylene Integration of regenerated PE French manufacturing Suppliers located within a maximum radius of 1000 km from production sites Return to Front Weight Menu DEUTZ FAHR 800 - 1000 - 1200 Description Our new DEUTZ-FAHR concrete weight, in perfect harmony with the bodywork, gives a very accomplished finish to the overall look of the DEUTZ-FAHR tractor. Designed with elegant and sleekly muscled lines, it perfects DEUTZ-FAHR tractor's aggressive and sharp look Available in 800kg, 1000kg and 1200kg. Advantages Special DEUTZ-FAHR design, attractive and contemporary Affordable Perfect finishing quality Return to Front Weight Menu

AGRITOTAL SUPPLIES PATEER PARTS. TAKE A LOOK AT OUR RANGE HERE PATEER PICKUP HITCHES FP6000 BASIC RANGE FP6000 PREMIUM RANGE LYNCH PINS SX3 FP6000 BASIC RANGE REAR ATTACHMENTS Description Dropdown and pick up function eliminates the need for manually lifting implements onto drawbars. Mechanical push back version (FP6000 ED) give superior visibility of the hook and trailer ring from the cab. Advantages CEE approved models for most of the tractors’ ranges Increase working comfort, flexibility and productivity Manufactured from high strength wear resistant materials Robust, perfect finish quality Versions FP6000 E CEE approved Affordable Without pushback FP6000 ED CEE approved Affordable 15cm mechanical pushback Optional: electrical control Return to pickup hitch menu FP6000 PREMIUM RANGE REAR ATTACHMENTS Description Dropdown and pick up function eliminates the need for manually lifting implements onto drawbars. These Mechanical and hydraulic high robust push back versions give superior visibility of the hook and trailer ring from the cab. Advantages FP6000 DP is CEE approved for most of the tractors’ ranges With pushback, working comfort, flexibility and productivity Manufactured from high strength wear resistant materials Robust, perfect finish quality Versions FP6000 DP CEE approved 16cm mechanical pushback Optional: electrical control FP6000 HD 38cm mechanical pushback Optional: electrical control Return to pickup hitch menu LYNCH PINS LYNCH PINS Description Our lynch pins are entirely made in Germany, from the design to the finished product, and are highly qualitative and resistant. Advantages Simple Safe Patented Models Ø5 x Lenght 32mm Ø6 x Lenght 42 mm Ø8 x Lenght 42 mm Ø10 x Lenght 45 mm Ø 11 x Lenght 45 mm Return to pickup hitch menu

AgriTotal is New Zealand's exclusive importer of Vervaet Beet Eater 617 harvester. View their online showroom today. Refurbished VERVAET BEET EATER 617 Sugar & Fodder Beet Harvester Vervaet’s Beet Eater 617 is the most economical machine on the market. The concept has been tested and proved for years, offering simplicity in operation yet also meeting the highest demands for quality, comfort and capacity. The tank capacity is 17 tonnes, and at that size, it’s perfect for majority of tipping trailers on the market today. The four-wheel steering provides good agility, and we believe has a lower operating cost per hectare than any other brand of tank harvester available. Buying A Vervaet Factory Rebuild The overhaul process is carried out thoroughly at the Vervaet factory in The Netherlands before being sold. At the factory they check, replace and refurbish all wearing parts from front to back. All major components are guaranteed ready to meet the demands of the next beet season, giving the customer confidence going into the field. The rebuild process Used machines are steam cleaned on arrival before entering the workshops. Once cleaned they are driven into the factory workshop where they are thoroughly inspected by technical teams under the supervision of Service Managers. An appraisal is completed identifying all work to be carried out. If any parts are required for the overhaul, they are ordered straight away. Once the rebuild has been completed, the harvester is tested and carefully monitored for a 5hr process. It is also road tested and tweaked if necessary, to ensure it is running beautifully. The harvester is cleaned, guarded and valeted before delivery. REFURBISHED VERVAET MACHINES Have you ever considered buying a pre-loved machine? Agritotal supply refurbished Vervaet machines directly from the factory in the Netherlands. All of the second-hand 617 Beet Eater - Harvester machines return to the factory, are stripped completely, cleaned, repaired if needed, and reassembled and tested before being sold as a refurbished unit. If the cost of a new machine is beyond your budget, this could be a great option. Talk to us about buying a refurbished machine today. WATCH VIDEOS VIEW GALLERY For more information about products, accessories or prices, please contact us.

AgriTotal is New Zealand's importer of d'Hooghe Beach Cleaners. Buy d'Hooghe Beach cleaning equipment here. SIWI THE HITCH SYSTEM OF THE FUTURE Using SIWI Combi-Hitch, you can change between your attachments and trailers. You can use SIWI Combi-Hitch for many different tasks – from forage harvesting to muck spreading. There is unlimited scope to how you can effectively use the SIWI Combi-Hitch system. Fast changeover: Trailer changeover in under 30 seconds. Connect the trailer/attachment in less than five seconds. The correct electrical and hydraulic hoses connections every time. ISOBUS connection and PTO option. Extremely safe: No persons between machines No need to leave the tractor or forage harvester cab. Highest possible level of work safety. Excellent comfort: The system is operated from the tractor or forage harvester cab Backlash-free tow – easy to attach. Sales for: New Zealand | Fiji | Solomon Islands | Timor | Indonesia | Papua New Guinea | Vanuatu | New Caledonia | Cook Islands | Samoa TRACTOR MODULE TM800 MACHINE MODULE MM800 TRAILER MODULE VM800P TRAILER MODULE VM800 Tractor Module TM800 • Mounted on the tractor 3 point • Up to 8 hydraulic couplings and up to 2 x 6 pin power plugs • Cat 3 • Compatible with Trailer Module VM800 and VM800P • Compatible with: Pneumatic brakes, LS-system, ISOBUS and different control-boxes • Weight ca. 250 kg • Preferred power range 140hk to 450hk tractor Enquire now TM800 Machine Module MM800 • Mounted on the forage harvester or tractor • Can be mounted with hydra cover on forage harvester, or with hydra-module when used on a tractor • Compatible with Trailer Module VM800 • MM800 mounted with hydra-modul is compatible with; Pneumatic brakes, LS-system, ISOBUS and different control-boxes • Weight ca. 270 kg Enquire now MM800 Trailer Module VM800P • Trailer Module with PTO • Mounted on the trailer K80 ball • 8 hydraulic couplings and 2 x 6 pin power plugs • Compatible with Tractor Module TM800 • Compatible with: Pneumatic brakes, LS-system, ISOBUS and different control-boxes • Weight ca. 326 kg Enquire now VM800P Trailer Module VM800 • Mounted on the trailer K80 ball • Up to 8 hydraulic couplings and up to 2 x 6 pin power plugs • Compatible with Tractor Module TM800-C3 and Machine Module MM80 • Compatible with: Pneumatic brakes, LS-system, ISOBUS and different control-boxes • Weight ca. 150 kg Enquire now VM800

AgriTotal is New Zealand's exclusive importer of TRILO groundskeeping machines and accessories. MAREDO-GT SERIES Back to Maredo Veticutter GT180 Verticutter Maredo GT180 CountRo-Verticutter Scarifying machine CountRo-Verticutter Maredo, model GT180. A set of three Maredo GT180 scarifying units is suitable for the most common 3-piece greensmowers, including Toro, Jacobsen and John Deere. Technical specifications 1.2 mm thick carbide blades available Capacity: 18 holes in 4-6/hour Leaf thickness 0.9 mm Blade spacing 20 mm Working depth 0-15 mm Weight 40 kg Characteristics Quick change Standard with plastic collection trays and trolleys Unique operation; the blades rotate against the direction of travel Low ground pressure on the green Easy to work with Working depth adjustment by means of quick adjusters Fits standard on Toro, Jacobsen and John Deere three-piece green mowers A specific mounting kit is used for each make and model to mount the CountRo-Verticutter GT180 verticutter. Unique attachment for greens mowers. Counter-rotating so removes more material. Support roller front and rear. The two built-in brushes clean the entire surface width. Operates at mow speed. Follows the curves perfectly. Low ground pressure on the green. Simple to work with, like mowing. Quick change of attachments. Working depth adjustment by means of quick adjusters. The scarifier is supplied as standard with a collection tray and trolleys. Perfectly suited for E-drives due to gear reduction. Enquire Aerator GT190 Aerator Maredo GT190 Fraze-Groomer Aerator GT190 Fraze-Groomer. A set of three Maredo GT190 Fraze-Groomers is suitable for most common 3-piece greensmowers, including Toro, Jacobsen and John Deere. A specific mounting kit is used for each make and model to mount the GT190 Fraze-Groomer. Equipped with a very unique technology. Groomers or light scarifiers are ideal tools for keeping horizontal grass, growth and thatch under control. Common greens groomers and scarifiers can leave visible lines in the green that affect the roll of the ball. The blades of the GT190 Fraze-Groomer are set at a slight angle to the main axis. This causes the blade tips to make short, interrupted cuts. In the image that the GT190 leaves behind, the cuts are barely visible. This while just as much material is removed from the turf as by a scarifier. As soon as a shallow-rooted weed or POA plant is in the area to be treated, it is loosened in this way and thrown into the pre-assembled collector. Technical specifications Unique groomer; the blades rotate against the direction of travel The blades are mounted at an angle to the main shaft. As a result, the GT190 produces no visible lines but short slots Integrated brushes ensure a clean result Characteristics Support roller front and rear Equipped with transport trolleys Standard with plastic collection tray Leaf thickness 0.9 mm Blade spacing 20 mm Working depth maximum 5 mm Weight 40 kg A second unique feature of the GT190 Fraze-Groomer is that the main shaft rotates against the direction of travel. Thanks to a compact gearbox, the blades 'lift' the unwanted material out of the green instead of cutting through and 'pulling' into the slot in a normal direction of rotation. This is in contrast to a 'regular' scarifier that will cut the plant in half and work it further into the turf. The brush mounted between the blades also ensures that the seed heads of the POA plant will be thrown into the tray. The total operation is comparable to a treatment with a fine rake; it thins the turf by pulling out the unwanted material that is not (yet) properly rooted. The working depth can be set to approximately 2 – 5 mm. With the quick adjusters, the working depth of the GT190 Fraze-Groomer is easy to adjust to a maximum depth of 5 mm. It is advisable not to go deeper, because serious damage can be done to the turf. The thickness of the blade is 0.9 mm. A stainless steel collection tray is supplied as standard. The GT190 is an ideal tool for aerating and thinning out too compact turf. It is possible to work at mowing speed with the GT190. However, the slower you drive, the more intensive the mesh pattern. Enquire Aerator Maredo GT210 VibeSpiker-Aerator Aerator GT210 VibeSpiker-Aerator. A set of Maredo GT210 VibeSpiker-Aerator / spike aerator turns your greensmower into a spike aerator and allows you to use your greensmower more versatile. By means of a special and unique technique, the holes are made in the bottom without having to use a lot of weight. Technical specifications Equipped with trolleys as standard Spike thickness 3mm Hole distance 42 mm Number of holes 700/m² Working depth max. 35 mm Weight 54 kg Characteristics Operates at mow speed Thanks to the vibration, the machine can reach the maximum working depth of 35 mm without much weight The vibrating spikes will also loosen the compacted top layer Working depth can be adjusted by adjusting the front roller Minimal influence on the ball roll Quick way to loosen the top layer of your greens and tees What can sometimes be difficult with the 'ordinary' spike aerators is the fact that a lot of weight has to be used to push the spikes into the soil and the holes produced do not look good. This is always a problem for small machines because weight does not benefit a small machine. To solve this problem, Maredo developed an innovative technique that uses vibrations to drive the spikes into the ground without needing much weight. The six independent spike sections are mounted on a camshaft. As soon as this shaft is driven, the rolling spikes begin to vibrate. These vibrations help the spikes get into the ground. When the spikes are fully pushed into the soil, the vibrating spikes loosen the soil. Loosening the soil is important for reducing soil compaction and achieving healthy grass growth. It is possible to use the aerator GT210 at mowing speed, after which you can immediately play on the greens again. No disruption to players! Enquire Aerator GT210 Aerator Maredo GT230 HiSpeed-Corer Aerator GT230 HiSpeed Corer. A set of three Maredo GT230 HiSpeed-Corer units fits most common brands and types of greensmowers and turns into very unique coring machines that remove thatch in a very efficient way with minimal damage to the turf. This makes the use of your greensmower much more versatile and results in considerable cost savings. The English 'coren' means; pricking a plug out of the turf by using a hollow pin. Felt control on greens can be a stressful operation. Removing felt is usually an operation that takes a lot of time and patience. Often there is no time at all to fight thatch! It is a major operation for the grass on the greens and a green sometimes needs weeks to recover. For years, felt was removed with a scarifying machine. A scarifier is basically a rotary mower on its side, however a scarifier has a circumferential speed that is five times lower than that of a rotary mower. Technical specifications Supplied as standard with hollow pins with a diameter of 11 mm outside and 7 mm inside Tine size ID7 mm Distance between pins 42 mm Maximum adjustable working depth 25 mm Number of holes depending on driving speed 600-1400m² Weight 46 kg Characteristics The new way to remove felt Produces approximately 4 million holes per hour When driving at mowing speed, a square hole pattern is created 18 Greens can be processed in 4-5 hours Equipped with trolleys as standard Star, needle, fixed and smaller hollow pins are also available and are easy to change The good news is that there is a new and unique way to remove the felt: using the Maredo GT230 HiSpeed-Corer. Literally translated, this means: de-felter. The hollow pins in the GT230 cut a round hole and pull out a wad of felt; a nice cut is created. The pins penetrate the felt layer and because material is actually removed, the percentage of felt in the greens will quickly decrease. Because the holes heal within 2 to 3 days, the GT230 can be used very regularly, if necessary. The holes are then no longer visible and great for optimal absorption of spraying agents, fertilizers and irrigation. Ordinary scarifying cuts require a longer recovery time. The working depth can be easily adjusted by adjusting the front roller to a maximum depth of 25 mm. Various pins are available such as hollow, cross, slicer and solid pins. Easily interchangeable. NEW: Back brush to sweep sand/dew into just punched holes. Enquire Sweeper Maredo GT250 CountRo-Sweeper Sweeper GT250 CountRo-Sweeper. A set of Maredo GT250 CountRo-Sweeper units (set of 3) fits most common brands and types of greensmowers, turning them into a highly effective sweeping brush, or one that sweeps topdress material into the grass and aerator holes. Cleaning and keeping greens clean can be a time consuming chore. Often large blowers are the only option to remove pine needles, excess topdress sand, felt plugs, worm piles or other debris from the green. Most brushes are not suitable for use on the green because they are too heavy or too aggressive. The GT250 is also perfect for brushing dew off the greens. Technical specifications Comes standard with collection trays Bristle diameter 1 mm Depth 0-12mm Weight 35 kg Characteristics Very efficient thanks to counter rotation Easy collection of cores or felt plugs from GT230 or other aerators Ideal for sweeping up worm piles, pine needles, dew and much more No damage to the turf due to reduced speed Topdress sand can also be swept in with the optional deflector plate The Maredo GT250 sweeper or sweeping brush is the only brush that rotates at a lower speed against the direction of travel. Thanks to the compact gearbox, the direction of rotation is reversed and the brushes then rotate against the direction of travel. This direction of rotation is the most efficient direction to clear material. The gearbox also reduces the speed of the brushes. With this lower speed, there is no longer a chance that the grass will 'burn' due to the excessive speed at which the brushes move over the grass. The brush height is easy to adjust by turning the height adjusters in or out. The machine is supplied with plastic collectors as standard (the standard greens mower collectors do not fit the GT250) Another application is brushing in sand-topdress material. The GT250 features a reversible faceplate that once flipped puts the topdress material back on the ground (directly into the aeration holes or into the grass) instead of ejecting the material into the collector. Some customers use the units to brush up the dense grass. Thanks to the fact that the brush rotates in the opposite direction, it is possible to thin out the grass slightly or to cut the grass perfectly short immediately after. Enquire Aerator GT230 Sweepe GT250 Greensroller Maredo GT300 VibeShoe Roller Greensroller Maredo GT300 VibeShoe Roller. A set of Maredo® GT300 VibeShoe-Roller units fits most common brands and types of greensmowers and makes your green faster. On a green, good ball roll and speed are key concepts. Stimp value and a consistent ball roll are important issues that a greenkeeper has to deal with on a daily basis. Rollers are often used to increase the stimp value and give the greens a consistent ball roll direction. However, a roller often tends to push material forward. As soon as there is enough resistance, the roller will roll over it and leave a wavy pattern. The disadvantage of a roller is always that it will always only apply pressure in one direction to smooth out. Technical specifications The most consistent greensroller Vertical impact is set by adjusting the front roller Ideal to 'vibrate' on topdress sand Increases ball speed and green stim value Characteristics Equipped with trolleys as standard Depth 0-12mm Weight 55 kg The Maredo GT300 VibeShoe-Roller works differently; the GT300 consists of six perfectly balanced sections (so no vibrations) designed as six 'feet'. As soon as there is an unevenness on the green, the best option is to correct this with the shoe. The GT300 consists of six rounded shoes per unit that, at high speed, make a short rolling movement; they 'walk' over the green, as it were. Pressing down on the turf smoothes the whole surface, increases the stimp value and keeps it more constant, thanks to the fact that the shoes make a small stepping motion, so that the feet don't 'drag' across the green. With the right settings, a stimp increase of 25 – 30% is possible in one go! Another application of the GT300 is brushing in or working in topdress material. The height is then adjusted so that the vibrating plates just touch the topdress material. Thanks to the vibration and pressure from above, the topdress material will end up in the right place between the grass. Enquire Greensroller GT300 Overseeder Maredo GT410 VibeSpike-Seeder Overseeder GT410. A set of Maredo GT410 VibeSpike-Seeder units fits all common brands and types of greensmowers. Is especially suitable for Ostrich and turns it into an overseeder for greens and tees. Every greenkeeper likes to see a strong turf on his green. A turf that is resistant to disease, is healthy and shows an even growth. Regular overseeding is necessary to create a strong turf. The problem with overseeding is usually that it is a time consuming activity and requires large machines that cause soil compaction. The solution is the Maredo GT410. This is a unique, patented and innovative overseeder that is not only fast, but also overseeders very neatly and efficiently. Technical specifications Equipped with trolleys as standard Spike depth 7-15mm Up to 1200 m² Dosage 1.4-18 gr/m² Seed container capacity 2 kg Characteristics Reduces seeding costs thanks to low dosage & high efficiency Fast action: 18 greens in 5-7 hours No game interruption Makes small holes through spikes. The six spike sections per unit roll over the grass and are mounted on a camshaft. Once the drive is engaged, the spikes easily vibrate to the pre-set depth. This prepares a perfect seedbed for the seed. The grass seeds are sown from the front, where the seed box is also located, the dosing shaft in the seed box is driven by the front roller. The dosage can be set via interchangeable gears in the compact gearbox. It is possible to dose up to a minimum of 2 grams per square meter. Once the seed lands directly in front of the spike through the funnels, the spike tip will take the seed and plant it precisely in the perfect seed bed. The rear-mounted brush will pick up any seeds that fall between the spikes and sweep them into one of the holes. Behind it is the rear roller that rolls the whole neatly flat. After that, no further processing is required. The greens are immediately playable again. And since the overseeding of 18 holes only takes 4-5 hours, you can do the overseeding while playing. Enquire Overseeder Maredo GT424 VibeTine-Seeder The Maredo GT424 VibeTine-Seeder is a very fast and efficient overseeder for red fescue (grass). The GT424 is perfect for overseeding greens, tees and front greens. Technical specifications Equipped with trolleys as standard Spike depth 7-15mm Area 900/m² Dosage Kentucky 5-32 gr/m² Dosage Fescue 2.5-14 gr/m² Seed container capacity 2 kg Weight 68 kg Characteristics Fast operation No game interruption Overseeding should be done regularly to create a strong and healthy top layer. However, regular overseeding can be a time consuming activity. The Maredo GT424 overseeder changes this. Thanks to the unique, clean and efficient way of overseeding with a three-piece greensmower, it is now possible to overseed as quickly and cleanly as possible. The GT424 can also be used for efficient sowing of all other types of granulate in your top layer of turf. Six tine sections create a perfect hole pattern. Seed hoppers are mounted directly behind these tines, which allow the seed to fall directly into the holes. A mounted brush helps to get all the seed in the holes. Enquire Oveseeder GT410 Overseeder GT424

AgriTotal is New Zealand's importer of d'hooghe beachcleaners. Buy d'hooghe Junior beach cleaning equipment here. The Beachcleaner Junior is ideal for small beaches. Easily maneuverable for cleaning around objects like sunshades, beach cabins, lakes, etc. d'Hooghe beachcleaners junior Mobile and precise The d'hooghe Beachcleaner Junior is extremely suitable for small beaches. Perfectly usable for cleaning around sunshades, beach cabins, lakes, etc. The d'hooghe Beachcleaner Junior is ideal for small beaches. Perfectly usable for cleaning around sunshades, beach cabins, lakes, and other objects you may find on the beach. No lugging of converted walking tractors or hand operated drilling machines. Even the discharge can be done hydraulically in containers. The Junior is a compact and maneuverable professional beach cleaner dragged by small or compact horticultural tractors. Everything you need can be put away in the integrated storage area which is equipped with gas pressure compensation for opening the lid and tool box. Side protection panels can be locked, equipped with gas pressure compensation with a maximum opening, enable a comfortable entrance to all necessary adjustments in order to perfectly adapt the configuration. The Junior offers a quality, work comfort, operational safety and user-friendliness superior to other compact mobile beach cleaners. WATCH VIDEO For more information about products, accessories or prices, please contact us.

Scam beach equipment represent the most widely used beach cleaning machines in the US domestic market and the international beach cleaning machines market Pioneers in cleaning of beach sand. They have manufactured beach cleaning equipments for more than 35 years. SCAM BEACH CLEANERS Scam beach equipment represent the most widely used beach cleaning machines in the US domestic market and the international beach cleaning machines market Pioneers in cleaning of beach sand. They have manufactured beach cleaning equipments for more than 35 years. Used in over 40 countries and 5 continents, these special beach equipments are world leader. They are effective in removing beach pollution such as seaweed, fish, glass, syringes, plastic, gans, cigarettes, shells, wood and other unwanted debris. These machines are able to remove from beach sand oil and tar balls after oil spill disasters. That’s why today to keep a beach clean is easy. Thanks to Scam special products, characterized by high quality and technology, beach pollution will be just a dream. Walk behind cleaners - Scam Tractor Cleaners - Scam Walk Behind Cleaners Cavalluccio Small size walk-behind beach cleaning machine ideal for cleaning of sandy areas (beaches, golf courses bunkers, playgrounds, beach volley fields, etc.). The front vibrating screen system, the interchangeable sieves with various meshes shaped as a "step" and the high-frequency vibration allow the full sieving of the sand loaded by the blade, separating the waste which will fall into practical fiberglass container, extractable. The depth of the work is controlled by the operator acting on the steering wheel of which the machine is equipped. The machine is supplied with 3 strong sieves with different meshes. The gearbox is equipped with two forward speeds plus two reverse gears. The machine is equipped with a locking device of the differential, activated by a lever. Maneuverability is insured by independent brake equipment mounted on each wheel the machine complies with ce regulations. More info on the Cavalluccio - Scam Website Ondina Small size walk-behind beach cleaning machine ideal for cleaning of sandy areas (beaches, golf courses bunkers, playgrounds, beach volley fields, etc.). The rear vibrating screen system, the interchangeable sieves with various meshes shaped as a "step" and the high-frequency vibration allow the full sieving of the sand loaded by the blade, separating the waste which will fall into practical steel container, extractable. The depth of the work is controlled by the operator acting on the steering wheel of which the machine is equipped. The machine is supplied with 2 strong sieves with different meshes. The gearbox is equipped with 2 forward speeds + 2 reverse gears and differential. The machine is equipped with a locking device of the differential, activated by a lever. The machine complies with ce regulations. More info on the Ondina - Scam Website Scorpion Self propelled beach cleaning machine useful to clean any sandy area (BEACH, GOLF COURSES BUNKERS, PLAYGROUNDS, BEACH VOLLEY FIELDS, ETC.) Same vibrating screen functioning and operation, new modifications make the machine very efficient: - More powerful engine HONDA GX200 - Better traction with new tyres 25” - Deeper cleaning - Wider cleaning - Bigger screen - Higher capacity - Stronger brakes - Reinforced idle Among its benefits the Scorpion machine is only 4 kg heavier and 2cm longer compared to Cavalluccio. THE MACHINE COMPLIES WITH CE REGULATIONS More info on the Scorpion - Scam Website Tractor Cleaners Walk behind Scam Pinguino Tractor-towed beach cleaning machine, small-sized perfect to be used with 4-wheel drive tractors (24-30cv), ideal for cleaning of sandy areas (beaches, golf courses bunkers, playgrounds, beach volley fields, etc.). The vibrating screen system, the interchangeable sieves with various meshes shaped as a "step" and the high-frequency vibration allow the full sieving of the sand loaded by the blade, separating the waste which will fall into practical steel container emptied hydraulically. The depth of the work is controlled by the operator acting on the tractor's hydraulic lifter. The machine is supplied with 2 strong sieves with different meshes. The machine is equipped with a propeller shaft with controlled force for the connection with the tractor’s power takeoff. The machine complies with ce regulations. More info on the Pinguino - Scam Website Tractor cleaners Scam

AgriTotal are New Zealand's importer of Horger Maschinen artificial turf cleaners and have a range of models and accessories available. artificial turf CLEANER sku AgriTotal import Horger Maschinen artificial turf cleaners to New Zealand. Flow Filled artificial turf is influenced by the environment from the first day on. Dust, pollen, plant particles and abrasion material are washed by rain into the fine cavities of the filling. The result is a total hardened surface without water permeability. The covering infiltrated with particles of humus causes the ideal breeding ground for algae and moss. An artificial turf that is dirty, no longer meet the purpose it was designed for. The risk of slipping becomes extreme and the potential of injury or accident high. Only with consistent maintenance and care can a filled artificial turf maintain its quality and be used effectively for many years. For effective care it is necessary to pick up the filling material off the turf pile in regular intervals. Coarse soiling’s are to be sieved and fine dust filtered. The bent turf fibres shall be reset upright and the filling material brought back to the turf fibres for stabilization. The surface will display an even level after treatment. To be able to work reliably and inexpensively Horger developed their artificial turf cleaner SKU as an assembling unit for compact tractors. There are three different processes that can be done with this machine due to its big brush diameter of 500 mm. 1. Maintenance cleaning: Depending on weather every two to four weeks. Coarse soiling and accumulated dust as well as abrasion is removed. 2. Intensive cleaning with loosening: About every 3 months. Coarse soiling is removed, fine particles like dust, plant rests and abrasion is filtered, filling is loosened, elasticity and drainage effect is maintained. 3. Reactivation of a surface untreated for several years: The hardenings are broken up, most of the filling is taken up, loosened, led back and extensively brought back into the turf pile. Coarse soiling is removed, fine particles, responsible for hardenings, are filtered. The hardened filling is loosened, the artificial turf is loose and flexible again, accident risk decreases and drainage effect is repaired. WATCH VIDEO GALLERY For more information about products, accessories or prices, please contact us.